eve模拟器：Cisco无线控制器C9800-CL

 eve模拟器：Cisco无线控制器C9800-CL

无线控制器_10.12.160.4_2024.12.22.16时19分09秒.txt

把接口切换三层接口

interface GigabitEthernet3
 no switchport

模板：

默认不需要密码

WLC>enable
WLC#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
WLC(config)#

WLC#show version
Cisco IOS XE Software, Version 17.03.04
Cisco IOS Software [Amsterdam], C9800-CL Software (C9800-CL-K9_IOSXE), Version 17.3.4, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2021 by Cisco Systems, Inc.
Compiled Sat 03-Jul-21 01:23 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2021 by cisco Systems, Inc.
All rights reserved.  Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0.  The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY.  You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.  For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
WLC uptime is 4 minutes
Uptime for this control processor is 6 minutes
System returned to ROM by reload
System image file is "bootflash:packages.conf"
Last reload reason: Unknown reason
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
AIR License Level: AIR DNA Advantage
Next reload AIR license Level: AIR DNA Advantage    
Smart Licensing Status: Registration Not Applicable/Not Applicable
cisco C9800-CL (VXE) processor (revision VXE) with 4106338K/3075K bytes of memory.
Processor board ID 9V7LGRX1P6W
Router operating mode: Autonomous
1 Virtual Ethernet interface
8 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
8106640K bytes of physical memory.
14589951K bytes of virtual hard disk at bootflash:.
Installation mode is INSTALL
Configuration register is 0x2102
WLC#

WLC#show interfaces status
WLC#show interfaces summary

interface GigabitEthernet1
 switchport mode access
!
interface Vlan1
 ip address dhcp
!

https://192.168.125.179

WLC(config)#user-name admin
WLC(config-user-name)#privilege 15
WLC(config-user-name)#password 0 admin
WLC(config-user-name)#type mgmt-user

user-name admin
privilege 15
password 0 admin
type mgmt-user

\

!配置自动修改了
interface GigabitEthernet1
 switchport trunk allowed vlan 1
 switchport mode trunk
 negotiation auto
 no mop enabled
 no mop sysid
!

!
interface Vlan1
 ip dhcp client client-id ascii cisco-001e.7ab7.41ff-Vl1
 ip address 192.0.2.2 255.255.0.0 secondary
 ip address 10.12.160.99 255.255.0.0
 ip helper-address 192.168.125.1
 no mop enabled
 no mop sysid
!

手动配置默认路由：WLC(config)#ip route 0.0.0.0 0.0.0.0 10.12.12.253

配置远程：

--------------------------------------------------------------------------
line vty 0 4
 no login  #如果配置上no login,则telnet时会直接无需输入密码到用户模式。
连接测试：
telnet 10.12.160.99
WLC>
WLC>enable
% No password set
WLC>


--------------------------------------------------------------------------
line vty 0 4
 login
 transport input all
连接测试：
telnet 10.12.160.99
Password required, but none set

--------------------------------------------------------------------------
line vty 0 4
 password Acisco@321
 login
 transport input all
连接测试：
telnet 10.12.160.99
Password required, but none set
ser Access Verification
Password:
WLC>en
WLC>enable
% No password set
WLC>
提示没有配置enable密码


--------------------------------------------------------------------------
line vty 0 4
 password Acisco@321
 login
 transport input all
连接测试：
telnet 10.12.160.99
Password required, but none set
ser Access Verification
Password:
WLC>en
WLC>enable
% No password set
WLC>
提示没有配置enable密码

也可以不用配置enable密码就直接进入到特权模式：
WLC(config)#line vty 0 4
WLC(config-line)# login local

line vty 0 4
 password Acisco@321
 login local
 transport input all
连接测试：
telnet 10.12.160.99
User Access Verification
Username: admin
Password: admin
WLC#
WLC#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
WLC(config)#
备注：前提是已经配置了用户
user-name admin
 creation-time 1734838391
 privilege 15
 password 0 admin
 type mgmt-user
!